5 cavity classes
4 shades
3 seconds
2 viscosities
1 universal composite
Your benefits
4 shades
- Just 4 shades cover all VITA* classical shades and Bleach shades
- Easy shade matching and exceptional shade adaptation thanks to the chameleon effect
- Natural esthetics for single-shade restorations in all cavity classes
4 mm
- 4-mm layer thicknesses for increased efficiency
- Can be applied in individual layer thicknesses between 0.1 and 4 mm
- Reliable curing, starting from 3 seconds[8]
4 quadrants
- Simplified universal composite
- Suitable for all five cavity classes, including use in the anterior region
- Tetric plus can be flexibly combined with dentin-shaded composites, for example for large Class III and IV restorations or in cases of severely discoloured dentin
4 fillers
- 4 fantastic fillers for high quality and convenient handling
- Esthetics suitable even for the anterior region
High-quality universal composites have made single-shade restorations increasingly popular, even in the anterior region. However, bulk-fill composites – designed for larger increments – have traditionally been considered less suitable for highly esthetic restorations. Tetric plus sets a new standard: Its optimized formulation bridges the gap between esthetics and increment thickness, allowing increments of up to 4 mm while maintaining impressive esthetics.
For larger, esthetically demanding Class III and IV restorations or in cases of discoloured dentin, Tetric plus can also be combined with other composites, such as the dentin shades from the Tetric Line.
In its uncured state, Tetric plus is highly translucent, allowing reliable and rapid light curing in layers of up to 4 mm. After curing, Tetric plus achieves enamel-like translucency. The final translucency develops within 24 hours after polymerization, providing a natural esthetic appearance that is also suitable for use in the anterior region.
Initial situation following trauma on tooth 22
Source: Dr Martin von Sontagh, Austria
Source: Dr Martin von Sontagh, Austria
Result immediately after treatment
Source: Dr Martin von Sontagh, Austria
Source: Dr Martin von Sontagh, Austria
Recall appointment showing the final result
Source: Dr Martin von Sontagh, Austria
Source: Dr Martin von Sontagh, Austria
High quality and convenient handling
Tetric plus Fill
Tetric plus is a sculptable universal composite that can be applied in layers up to 4 mm in thickness.
Handling
- Sculptable viscosity that adapts well to cavity walls
- 92% of dentists report high satisfaction with the cushioning effect[1]
- Viscosity can be adjusted by heating the material, if desired
Mechanical properties
- Reliable curing[2] of layers up to 4 mm, ensuring strength and longevity
- High radiopacity[2] >200% Al for easy diagnostics
- Very good mechanical properties for high strength:
– High flexural strength[2] (133 MPa) and compressive strength (375 MPa)
– Low wear - Low shrinkage stress for a reduced risk of marginal gaps
- High bond strength with Adhese Universal for sound marginal integrity
- Low water absorption[2] of 21 μg/mm3 for improved stability
Tetric plus is a sculptable universal composite that can be applied in layers up to 4 mm in thickness.
Handling
- Sculptable viscosity that adapts well to cavity walls
- 92% of dentists report high satisfaction with the cushioning effect[1]
- Viscosity can be adjusted by heating the material, if desired
Mechanical properties
- Reliable curing[2] of layers up to 4 mm, ensuring strength and longevity
- High radiopacity[2] >200% Al for easy diagnostics
- Very good mechanical properties for high strength:
– High flexural strength[2] (133 MPa) and compressive strength (375 MPa)
– Low wear - Low shrinkage stress for a reduced risk of marginal gaps
- High bond strength with Adhese Universal for sound marginal integrity
- Low water absorption[2] of 21 μg/mm3 for improved stability
Tetric plus Flow
Tetric plus Flow is a flowable universal composite that can be applied in layers up to 4 mm in thickness.
Handling
- Universal viscosity thanks to exceptional thixotropic properties
– Precise application and high stability[3]
– Good flowability[4] for fast volume replacement - Adapts to cavity walls and has a self-levelling effect
- Even with 4-mm layers, no additional covering layer is needed due to the material's very good mechanical properties[5]
Mechanical properties
- Reliable curing[2] of layers up to 4 mm, ensuring strength and longevity
- High radiopacity[2] >200% Al for easy diagnostics
- Very good mechanical properties for high strength:
– High flexural strength[2] (133 MPa) and compressive strength (375 MPa)
– Low wear - Low shrinkage stress for a reduced risk of marginal gaps
- High bond strength with Adhese Universal for sound marginal integrity
- Low water absorption[2] of 21 μg/mm3 for improved stability
Tetric plus Flow is a flowable universal composite that can be applied in layers up to 4 mm in thickness.
Handling
- Universal viscosity thanks to exceptional thixotropic properties
– Precise application and high stability[3]
– Good flowability[4] for fast volume replacement - Adapts to cavity walls and has a self-levelling effect
- Even with 4-mm layers, no additional covering layer is needed due to the material's very good mechanical properties[5]
Mechanical properties
- Reliable curing[2] of layers up to 4 mm, ensuring strength and longevity
- High radiopacity[2] >200% Al for easy diagnostics
- Very good mechanical properties for high strength:
– High flexural strength[2] (133 MPa) and compressive strength (375 MPa)
– Low wear - Low shrinkage stress for a reduced risk of marginal gaps
- High bond strength with Adhese Universal for sound marginal integrity
- Low water absorption[2] of 21 μg/mm3 for improved stability
4 mm for higher efficiency. 4 shades for greater simplicity.
Our technologies for greater esthetics, quality and efficiency
With Tetric plus, we have optimized every component, in particular the 4-filler technology. The combination of spherical and non-spherical fillers of various sizes enhances the material's handling, strengthens its mechanical properties and allows for quick polishing.
This combination also has a significant impact on the material's chameleon effect: The four different filler types are precisely coordinated to scatter incoming light optimally, while the monomer matrix intensifies this effect with carefully adjusted, intentionally varied refractive indices.
We have measured and analyzed the tooth colours of nearly 400 people. In doing so, we were able to identify four shade clusters that optimally cover the colour spectrum of natural teeth. Based on these four clusters and in line with the VITA* shades, we formulated Tetric plus.
Tetric plus is designed to deliver an enhanced chameleon effect. With just four shades, you can cover the entire spectrum of natural tooth colours. In its cured state, Tetric plus absorbs and scatters light similarly to natural tooth structure, allowing it to blend almost seamlessly with the surrounding tooth colour. This effect is achieved through the ideal interaction between monomers, fillers and pigments.
Tetric plus is a light-curing dental material. To enable reliable and quick light-curing, Tetric plus is translucent before polymerization. The yellowish tint makes it easier to identify unpolymerized areas.
The final translucency develops within 24 hours after polymerization,
providing a natural esthetic appearance that is also suitable for use in the anterior region.
Tetric plus Fill A3 plus
Translucency before polymerization: 36 %
Translucency after polymerization: 12 %
The requirements placed on 4-mm composites are more demanding, as the thicker layer must not cause increased shrinkage stress during polymerization.
Our solution: The patented chain regulator. Together with the shrinkage stress reliever — a special filler with an exceptionally low elasticity modulus — the chain regulator reduces both volumetric shrinkage and shrinkage stress. As a result, the shrinkage stress of Tetric plus is comparable to that of conventional composites.
Ivocerin is our patented light initiator, which we have already been using for Tetric PowerFill and Tetric PowerFlow. It provides for efficient curing of layer thicknesses up to 4 mm. The highly reactive light initiator enables fast and reliable polymerization – for durable, long-lasting restorations and a more efficient treatment workflow.
Product Comparison
* No registered trademark of Ivoclar.
** Note the maximum layer thickness of 3.5 mm for the shade A3.5 plus when choosing a curing time of either 3 s or 5 s. For further details please refer to the Instructions for Use of the respective product.
*** Only suitable for Class I & II restorations in posterior teeth light-cured from the occlusal aspect.
[1] Internal study based on over 170 participants. 92% reported experiencing "no" or "hardly noticeable deformations".
[2] According to ISO 4049.
[3] Internal study based on over 170 participants. 89% of the participants rated the stability of Tetric plus Flow as "very good" or "good".
[4] Internal study based on over 170 participants. 91% of the participants rated the flowability of Tetric plus Flow as "very good" or "good".
[5] For load-bearing restorations, apply a covering layer of a sculptable composite.
[6] Internal study based on over 170 participants.
[7] Note the maximum layer thickness of 3.5 mm for the shade A3.5 plus when choosing a curing time of either 3 s or 5 s.
[8] With Bluephase PowerCure in the 3sCure mode (light intensity of 2700–3300 mW/cm2). Only suitable for Class I and II restorations in the posterior region, light-cured from the occlusal aspect.